Want to see correct answers?
Login or join for free!
  printable Worksheets
Looking for printable worksheets?
Check out our pre-made printable worksheets!
Share/Like This Page
Filter By Grade

Grade 9 College Continuing Education

Browse Questions

Hand Tools Questions - All Grades

You can create printable tests and worksheets from these Hand Tools questions! Select one or more questions using the checkboxes above each question. Then click the add selected questions to a test button before moving to another page.

Previous Page 1 of 5 Next
Continuing Education Hand Tools
What type of leveling tool is used to check walls for plumb and is hung from a string?
  1. Plumb bob
  2. Chalk line
  3. String line
  4. Level line
Continuing Education Hand Tools
The term plumb refers to the                 .
  1. horizontal plane
  2. vertical plane
  3. both
  4. none
Continuing Education Hand Tools
The term level refers to the                 .
  1. horizontal plane
  2. vertical plane
  3. both
  4. none
Continuing Education Hand Tools
This type of nailing technique is used to fasten 2 pieces of wood together when end nailing is not an option.
  1. Angle nailing
  2. Toe nailing
  3. Finish nailing
  4. Pneumatic nailing
Continuing Education Hand Tools
This type of tool is used to pull nails and has another name than nail puller.
  1. Nail remover
  2. Cat's paw
  3. Pry bar
  4. Nail pull
Continuing Education Hand Tools
What can be done to a nail to reduce the chance of the material splitting?
  1. Cut off the point
  2. Blunt the point by hitting it with a hammer
  3. Hammer really slowly
  4. Hammer really lightly
Continuing Education Hand Tools
If you are having difficulty pulling a nail from a piece of material, what is the most efficient way to increase the leverage of the hammer you are using?
  1. Add a block under the hammer
  2. Add a pipe to the end of the hammer
  3. Use a different hammer
  4. Drive the nail in until it protrudes to the other side
Continuing Education Hand Tools
When clamping material together, what is something that needs to be avoided to prevent damaging of material?
  1. Over clamping, which causes dents
  2. Using the wrong clamp
  3. Under clamping, which doesn't create a sufficient hold
  4. All of the above
Continuing Education Hand Tools
What are the two most common types of claw hammers that are used in carpentry?
  1. Framing
  2. Finishing
  3. Straight
  4. Roofing
Continuing Education Hand Tools
What tool would give you the most accurate reading when measuring board thickness?
  1. Metal ruler
  2. Speed square
  3. Tape measure
  4. Caliper
Continuing Education Hand Tools
This type of level is small and used to check areas for plumb or level that would not require a 2' or 4' level.
  1. Mini level
  2. Torpedo level
  3. Small level
  4. Hand level
Continuing Education Hand Tools
Which of the following types of clamps will do the least damage to material when applying pressure?
  1. Spring clamp
  2. Bar clamp
  3. Band clamp
  4. Edge clamp
None Hand Tools
Identify the tool in the image.
Carpentry Tools - Speed Square
  1. Rafter square
  2. Bevel square
  3. Framing square
  4. Speed square
Continuing Education Hand Tools
When checking for plumb on a vertical stud that has a bowed edge, where is it recommended to place the level on the stud for the most accurate reading?
  1. On the top
  2. On the bottom
  3. Along one edge in the middle
  4. With a straight edge running from the top to bottom of the stud
None Hand Tools
Identify the tool in the image.
Carpentry Tools - Angle Finder
  1. Speed Square
  2. T Bevel
  3. Sliding square
  4. Angle finder
Previous Page 1 of 5 Next